How to Make Injectable Winstrol in Oil(Winny) 50mg/ml

Injectable Winstrol Steroid Recipes for Male Muscle Growth

How to Make Injectable Winstrol in Oil 50mg/ml

Preparation:

• 1 Gram winstrol
• 1 20 ml glass vial or larger
• 1 20 ml sterile glass vial or larger
• 1 .45 Whatman sterile syringe filter.
• 2 5 or 10 ml syringes
• 2 3 ml syringes
• 3 18 or 20 gauge pins
• 2 22 gauge pins
• 17 ml of sesame seed oil
• 0.2 ml of benzyl alcohol
• 2 ml of guaiacol (super solvent)

Tip: This will make 20ml at 50mg/ml. Only try to convert winstrol powder 1 gram at a time, it is very easy to ruin it in the conversion

Steps:

	Step 1 Weigh out 1 gram of winstrol powder, you will need a scale use the tare function to take away the weight of the container that holds your powder, and weigh it out to 1 gram.
	Step 2 Draw out 2 ml of the super solvent, using 1 of the 3 ml syringes.
	Step 3 Place the powder in the open glass vial, then add the super solvent to the powder in the vial(Edited by Wumei Tech, All Rights Reserved.)
	Step 4 A:Place back on rubber stopper, put one of the 20g pins in the stopper. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat until powder disolves into a liquid (the melting point of winstrol is between 239.8-242 degrees F). Turn off heat, and let it cool down still in the pan, until it reaches room temp. again takes about 15 minutes. Vial will be VERY HOT, so use an oven mit. B:Also heat seseame oil (heat more than 17ml because you won’t get it all out) it can be heated on a stove eye, or in the oven, I heated mine in the oven in a muffin pan, the oil needs to reach 212 F., to help sterilize the oil. I put mine in the oven at 275 F. Just to make sure.
	Step 5 Draw out .2 ml of benzyl alcohol, this is 1% of the final solution. It is very important that you do not use more than 1% of the solution with winstrol, or it could crash when finished.
	Step 6 Add BA to the solution in the vial. Shake very gently.
	Step 7 A:Draw out the oil with the 10 ml syringe, (Be sure you have allowed it to cool down some) add the 15ml of oil to the solution. Shake very gently again. Note – After adding the oil to the solution the winstrol may begin to clump up back into a powder, if it does, you just need to reheat it again like in Step 4a, remember to let it cool slowly. My powder did this, and this took care of it.
	B:Save 2 ml of oil in the syringe, and re-cap it. You need this later during the sterile filter process to make sure none of the winstrol is left in the filter.
	Step 8 Place 1 of the 18 guage pins in the steile unopened vial, and attach the whatman sterile filter. Draw out the solution using the other 10ml syringe, attach to the filter, and slowly press solution into the sterile vial. Then use the remainding 2ml of oil in the other syringe, to run through the filter, to make sure that none of the winstrol is left in the filter.
	Step 9 After filtering, leave the pin in the sterile vial, remove the filter. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat solution for about 15 to 20 minutes. Turn off heat, and let it cool down still in the pan, until it reaches room temp. again this takes about 15 minutes.
	Finished Product Below is what your finished product should look like, it should be a light gold color. (unless you used Grape seed oil, then it will have a greenish tint to it

Edited by Wumei Tech, All Rights Reserved.